Stamp
Pads - Stone Stamp Pads |
Stone
Stamp Pads
This is the only stamp pad that can be used with
solvent/acid based industrial marking inks without
destroying the pad. A constant flow of ink from
the porous stone helps create high quality, non-smear
impressions. Sizes: #1, #2 & #3 |
Stamp
Pads
Mark-Hitt
Two-Part Epoxy Ink
Surfaces: Ceramics, phenolics, polyesters, melamines,
silicones, ferrous and non-ferrous metal, glass, electronics.
Drying Time: Air dry from 2-3 hours. Curing time can
be speeded up by adding heat. 7 to 10 days required
for maximum adhesion, and chemical resistance. Require
addition of a catalyst immediately prior to use.
Characterisics: Meets Spec. MIL-I-43553. A two-part
epoxy ink with a high degree of adhesion to the most
difficult surfaces. Becomes permanent after curing.
Excellent resistance to solvents and chemicals.
Colors: Black, White-1/2 oz. packets, quarts available.
Other colors available on special order.
Applications: Especially formulated for the electronics
industry for use with Markem, Prenco, Rezafix, Jan Tech,
Mark & Pack, Eastern and other parts marking machines.
May also be applied with a rubber stamp by rolling out
a thin film of ink with a brayer on a smooth surface.
|
Mark-Hitt
Invisible Stamp Ink
Surfaces:
Skin-Usually hands.
Drying Time: Instant.
Characterisics: Ink is made so that it will show up
only under a Black ultraviolet light. Used for identification
purposes at dances, pools, private picnics, etc.
Colors: Blue-when under light.
|
Mark-Hitt
No. 214 Stamp Ink
Surfaces:
For stamping semi-absorbent and non-absorbent surfaces
such as flossy paper, painted surfaces, metal, hardwood,
electronic parts.
Drying Time: 30 to 60 seconds.
Characterisics: Good adhesion, non-acid, waterproof
- Approved by Dept. of Agriculture for use on food packages.
Colors: Black, Blue, Red, Purple, White, Yellow, Orange,
Green and Brown.
|
Mark-Hitt
Stamp Ink Thinner #141
For:
#141, Cellophane, Indelible, A. X., Opaque, #628, #214,
or any ink used with opaque pads. Characterisics: These
thinners have the same solvents used in each particular
ink. Only the color is eliminated. Will rejuvenate the
ink or pad and will bring it back to its original state
and drying time. Can also be used for cleaning rubber
stamps.
|
Mark-Hitt
Parachute Ink #6903
Surfaces:
Nylon parachute cloth, parachute pack cloth and webbing.
Drying Time: Within 10 seconds after stamping on material.
Characterisics: When applied with rubber stamp, will
produce a sharp legible impression, indelible. Meets
Govít. Spec. MIL-I-6903.
Colors: Strata Blue, Orange-Yellow, Red, Black.
|
Mark-Hitt
Metal Marking & Stenciling Ink
Surfaces:
For marking and stenciling iron, steel drums, boilers,
sidewalks and any painted or non-absorbent surface.
Drying Time: Will set to touch in 5 minutes. Will dry
in 10 to 15 minutes.
Characterisics: To be used with ordinary pot and stencil
brush. Can be prepared for use in fountain brush if
order is made to read "Metal F.B.". Ink has
good adhesion, is rub resistant and waterproof. Govít.
Spec. TT-1-558 and MIL-1-1795A Type 1.
Colors: Black, Red, Blue, Green, White, Yellow, Orange,
Brown, Silver. Matched and Govít. colors can be made
to order.
|
Mark-Hitt
No. 432 Ink
Surfaces: Metal parts, plastic parts, printed circuit
boards, glass, polyethylene, polypropylene excellent
adhesion on all hard to mark surfaces.
Drying Time: 15-30 seconds. The longer this ink is allowed
to dry, the harder the impression becomes, making it
more resistant to solvents and other washes.
Characterisics: Made to resist solvents such as degreasers,
freon, alcohol, trichloroethylene, cleaning fluids,
soap water.
Colors: Black, White, Yellow, Red, Blue, Orange, Green,
Purple.
|
Mark-Hitt
Indelible Ink
Surfaces:
Absorbent surfaces, linen, hosiery.
Drying Time: Almost immediately, depending on absorbency
of material.
Characterisics: Will withstand many washings. Can be
used with rubber or metal stamp or stencil if used sparingly.
Colors: Red, Blue, Green, Purple, Yellow, White.
Mark-Hitt No. 245 Stamp Ink Surfaces: Any non-absorbent
material. Very good for all types of cellophane.
Drying Time: 3-5 seconds.
Characterisics: A very fast drying ink that has excellent
adhesion on most non-absorbent surfaces. Makes sharp
impressions that are very rub resistant. Good for production
line work because of its quick drying characteristics
and ability to adhere to a wide varient of materials.
Approved by Dept. of Agriculture for use on food packages.
|
Mark-Hitt
No. 628 Polyethylene Stamp Ink
Surfaces:
Treated Polyethylene, plastics, metal and most non-absorbent
surfaces.
Drying Time: 5-10 seconds.
Characterisics: Quick drying, waterprood, Excellent
Adhesion. Very good on hard to mark polyethylene. Comes
in vivid pigmented colors. Will not migrate through
plastic. Conforms to Govít. Spec Mil-1-16557 a type
1. Approved by Dept. of Agriculture for use on food
packages.
Colors: Black, Red, Blue, Green Yellow, White, Orange,
Purple, Brown, RED conforms to Govít. Spec TT-1-554A.
Mark-Hitt A. X. Stamp Ink Surfaces: Non-absorbent-for
stamping and pen use on highly glazed surfaces, metallic
labels, painted surfaces, electronic parts, hardwood,
celluloid.
Drying Time: 30-60 seconds.
Characterisics: Acid base, good adhesion, etches slightly
into surface, waterproof. Govít Specs. TT-1-545a; TT-1-547a.
Approved by underwriter lab for use on electrical fixtures.
Colors: Black, Blue, Red, Green, Purple and Brown.
|
Mark-Hitt
Indelible Laundry Ink
Surfaces:
Used with pen, rubber stamp or stencil for marking linen
and clothing.
Drying Time: Almost immediately-Depending on absorbency
of material.
Characterisics: Acid base. Will not bleach out, no preparation
or hot iron required, can be washed immediately after
marking. Not to be used on top of sizing. Govít. Spec.
TT-1-542.
Colors: Black. |
Mark-Hitt
476 Solvent Resistant Ink
Surfaces:
Metal parts, plastic parts, printed circuit boards,
glass.
Drying Time: 30-60 seconds depending on surface.
Characterisics: Made to resist solvents such as degreasers,
alcohol, cleaning fluids, etc. The longer this ink is
allowed to dry, the more resistant it will be to solvents.
Colors: Black, White, Yellow, Red, Orange, Green, Blue,
Purple. |
Mark-Hitt
No. 1250 Ink
Surfaces:
All non-absorbent surfaces such as metal, cellophane,
foil, resin coated photographic paper, mylar, chrome
coated labels, food packaging.
Drying Time: 10-15 seconds.
Characterisics: The ink specifically formulated for
use on the Mark 11 stamp pad. An excellent all purpose
ink. Waterproof, excellent adhesion, USDA approved for
food packaging. Conforms to Govít. Spec. TT-1-1795A,
Type 1, when a stamping ink is required. Also meets
Spec. MIL-16557A, Type 1.
Colors: Black, Blue, Red, Purple, Green, Brown, White,
Yellow, Orange, Silver. |
NOTICE:
While the manufacturer takes utmost care in compounding
& manufacturing these inks, we cannot guarantee
their performance. All inks are sold with the understanding
that our liability with respect to any defective ink
is limited to the replacement of the ink. |
|
|